Linksys WAP55AG v2

Linksys WAP55AG v2.0

Manuf (OEM/ODM): Gemtek WRTA-119AG

FCC approval date: 30 December 2004
Country of manuf.: Taiwan

Type: access point

FCC ID: Q87-WAP55AGV2
IC ID: 3839A-WAP55AGV2

Power: 5 VDC, 2.5 A
Connector type: barrel
Conn. measurements: 5.5 mm (OD), 2.0 mm (ID)

CPU1: Atheros AR5312A
FLA1: 2 MiB 2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> (Macronix MX29LV160BBTC-90G)
RAM1: 8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (ISSI IS42S32200B-6T)

Expansion IFs: none specified
Serial: yes, internal, 9-pin header, Gemtek type1 pinout, (9600,8,N,1), JP1

WI1 chip1: Atheros AR5312A
WI1 chip2: Atheros AR5112A
WI1 802dot11 protocols: a
WI1 antenna connector: U.FL
WI2 chip1: Atheros AR5312A
WI2 chip2: Atheros AR2112A
WI2 802dot11 protocols: bg
WI2 antenna connector: U.FL

ETH chip1: Atheros AR5312A
ETH chip2: IC+ IP101
LAN speed: 100M
LAN ports: 1

abg

Additional chips
2.4GHz Power Amplifier IC;Microsemi;LX5510;MSC, 5510, 531BU;1;InGaP/GaAs HBT;16-pin MLPQ;3 mm x 3 mm;
4.5 to 6GHz Power Amplifier IC;Microsemi;LX5506;MSC, 5506, 530CL;1;InGaP/GaAs HBT;16-pin MLPQ;

Stock FW OS: VxWorks

Default SSID: linksys-a (3 addl. devices)
, linksys-g (5 addl. devices)
Default IP address: 192.168.1.246
the IP 192.168.1.246 is used by 1 additional devices
of which 1 are Linksys devices
Default login user: blank
Default login password: admin
blank:admin credentials used by 300 additional devices
of which 143 are Linksys devices

802dot11 OUI: 00:12:17 (16 E, 32 W)
Ethernet OUI: 00:12:17 (16 E, 32 W)

	CPU1 brand	WI1 chip1 brand	WI2 chip1 brand
Linksys WAP55AG v1	Broadcom	Atheros	Broadcom
Linksys WAP55AG v2	Atheros	Atheros	Atheros

For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.

---

Dual-Band Wireless Access Point

 • Support page  • (Template link outdated)

• OEM: Gemtek WRTA-119AG (WRTA-119AG_V01)

Default credentials are per the FCC manual.

The default SSIDs for this device are linksys-a and linksys-g.

This device appears to support U-NII-2 channels, however, it may not implement Dynamic Frequency Selection (DFS) due to its age.

• On the DD-WRT forums (pictures)

Pinout

Credentials

The (default) credentials are the same as the router's default credentials.

Username: <blank>
Password: admin

Info derived from

• boot log

ar531x rev 0x00005742 firmware startup... SDRAM TEST SKIPPED Please check the ethernet cable on port 0 Atheros AR5001AP default version 4.0.0.48 Bootloader version 1.01 0 auto-booting... Attaching to TFFS... done. Loading /fl/APIMG1...1073872 Starting at 0x804846e0... /fl/ - Volume is OK Reading Configuration File "/fl/apcfg". Configuration file checksum: 4da56 is good Please check the ethernet cable on port 0! Attaching interface lo0...done vp0 macaddr = 00:12:17:77:41:30 vp65536 macaddr = 00:12:17:77:41:31 ae0 macaddr = 00:12:17:77:41:32 start easy conf wireless access point starting... wlan1 Ready wireless access point starting... Auto Channel Scan selected 5280 MHz, channel 56 wlan0 Ready Ready

• AP shell help

WAP55AG wlan0 -> ? List of Access Point CLI commands: add remoteWbr -- Add a remote Wireless Bridge config wlan -- config wlanX connect bss -- connect to bssX del acl -- Delete Access Control List del key -- Delete Encryption key del remoteWbr -- Delete a remote Wireless Bridge find bss -- Find BSS find channel -- Find Available Channel find all -- Find All BSS ftp -- Software update via FTP get acl -- Display Access Control List get aging -- Display Aging Interval get antenna -- Display Antenna Diversity get association -- Display Association Table get authentication -- Display Authentication Type get autochannelselect -- Display Auto Channel Select get beaconinterval -- Display Beacon Interval get burstSeqThreshold -- Display Max Number of frames in a Burst get burstTime -- Display Burst Time get channel -- Display Radio Channel get cipher -- Display Encryption cipher get config -- Display Current AP Configuration get countrycode -- Display Country Code get domainsuffix -- Display Domain Name Server suffix get dtim -- Display Data Beacon Rate (DTIM) get encryption -- Display Encryption Mode get fragmentthreshold -- Display Fragment Threshold get frequency -- Display Radio Frequency (MHz) get gateway -- Display Gateway IP Address get groupkeyupdate -- Display Group Key Update Interval (in Seconds) get hardware -- Display Hardware Revisions get hostipaddr -- Display Host IP Address get ipaddr -- Display IP Address get ipmask -- Display IP Subnet Mask get jsw -- Display Jumpstart Mode get key -- Display Encryption Key get keyentrymethod -- Display Encyrption Key Entry Method get keysource -- Display Source Of Encryption Keys get login -- Display Login User Name get minimumrate -- Display Minimum Rate get nameaddr -- Display IP address of name server get operationMode -- Display Operation Mode get pktLogEnable -- Display Packet Logging Mode get power -- Display Transmit Power Setting get radiusname -- Display RADIUS server name or IP address get radiusport -- Display RADIUS port number get rate -- Display Data Rate get reg -- Display the register contents at the given offset get remoteAp -- Display Remote Ap's Mac Address get remoteWbr -- Display configured Remote Wireless bridges get rtsthreshold -- Display RTS/CTS Threshold get sntpserver -- Display SNTP/NTP Server IP Address get ssid -- Display Service Set ID get ssidsuppress -- Display SSID Suppress Mode get station -- Display Station Status get SuperG -- Display SuperG Feature Status get systemname -- Display Access Point System Name get tzone -- Display Time Zone Setting get upsd -- Display UPSD Mode get uptime -- Display UpTime get vlan -- Display VLAN Mode get wirelessmode -- Display Wireless LAN Mode get wmm -- Display WMM Mode get wmmParamBss -- Display WMM parameters used by STA in this BSS get wmmParam -- Display WMM parameters used by this AP get wlanstate -- Display wlan state help -- Display CLI Command List ping -- Ping pktLog -- Packet Log reboot -- Reboot Access Point run -- Run command file quit -- Logoff set acl -- Set Access Control List set aging -- Set Aging Interval set antenna -- Set Antenna set authentication -- Set Authentication Type set autochannelselect -- Set Auto Channel Selection set beaconinterval -- Modify Beacon Interval set burstSeqThreshold -- Set Max Number of frames in a Burst set burstTime -- Set Burst Time set channel -- Set Radio Channel set cipher -- Set Cipher set countrycode -- Set Country Code set domainsuffix -- Set Domain Name Server Suffix set dtim -- Set Data Beacon Rate (DTIM) set encryption -- Set Encryption Mode set factorydefault -- Restore to Default Factory Settings set fragmentthreshold -- Set Fragment Threshold set frequency -- Set Radio Frequency (MHz) set gateway -- Set Gateway IP Address set groupkeyupdate -- Set Group Key Update Interval (in Seconds) set hostipaddr -- Set Host IP address set ipaddr -- Set IP Address set ipmask -- Set IP Subnet Mask set jsw -- Set Jumpstart Mode set key -- Set Encryption Key set keyentrymethod -- Select Encryption Key Entry Method set keysource -- Select Source Of Encryption Keys set login -- Modify Login User Name set minimumrate -- Set Minimum Rate set nameaddress -- Set Name Server IP address set operationMode -- Set operation Mode set password -- Modify Password set passphrase -- Modify Passphrase set pktLogEnable -- Enable Packet Logging set power -- Set Transmit Power set radiusname -- Set RADIUS name or IP address set radiusport -- Set RADIUS port number set radiussecret -- Set RADIUS shared secret set rate -- Set Data Rate set reg -- Set Register Value set remoteAP -- Set Remote AP's Mac Address set rtsthreshold -- Set RTS/CTS Threshold set sntpserver -- Set SNTP/NTP Server IP Address set ssid -- Set Service Set ID set ssidsuppress -- Set SSID Suppress Mode set SuperG -- Super G Features set systemname -- Set Access Point System Name set tzone -- Set Time Zone Setting set upsd -- Set UPSD Mode set vlan -- Set VLAN Mode set wlanstate -- Set wlan state set wirelessmode -- Set Wireless LAN Mode set wmm -- Set WMM Mode set wmmParamBss -- Set WMM parameters used by STAs in this BSS set wmmParam -- Set WMM parameters used by this AP timeofday -- Display Current Time of Day version -- Software version nvram -- nvram utility

• AP shell version + get hardware
WAP55AG wlan0 -> version AP software 4.0.0.80 mars@MARSNB:E:/AP_4.0.0.80_THGSrc_Src/ap/os/vxworks/target/proj/ap-ar5312-production Jan 26 2005, 16:54:11 WAP55AG wlan0 -> get hardware wlan0 revisions: mac 5.7 phy 4.2 analog 3.6 PCI Vendor ID: 0x168c, Device ID: 0x13 Sub Vendor ID: 0x168c, Sub Device ID: 0x13 chip is AR5312

• nvram show

WAP55AG wlan0 -> nvram show regulatory_domain=FCC country_domain=US wan_proto=static sys_name=WAP55AG wan_domain= lan_ipaddr=192.168.1.246 lan_netmask=255.255.255.0 dhcps_mode=enabled wan_dns= login_name= login_password=admin lan_gateway=192.168.1.1 wl0_ssid=linksys-a wl0_channel=0 wl0_stat_mode=enabled wl0_wirelessmode=11a wl0_ssid_bcast=enabled wl0_security_mode=disabled wl0_encrypt_idx=40 wl0_key_idx=1 wl0_key1= wl0_key2= wl0_key3= wl0_key4= wl0_cipher_type=tkip wl0_wpa_passphrase= wl0_wpa_group_key_interval=1500 wl0_auth_type=open wl0_transmission_rate=auto wl0_transmission_power=full wl0_frame_burst=enabled wl0_beacon_interval=100 wl0_dtim_interval=1 wl0_frag_threshold=2346 wl0_rts_threshold=2346 wl1_ssid=linksys-g wl1_channel=6 wl1_stat_mode=enabled wl1_wirelessmode=11g wl1_wirelessmode_tmp=11g wl1_ssid_bcast=enabled wl1_security_mode=disabled wl1_encrypt_idx=40 wl1_key_idx=1 wl1_key1= wl1_key2= wl1_key3= wl1_key4= wl1_cipher_type=tkip wl1_wpa_passphrase= wl1_wpa_group_key_interval=1500 wl1_auth_type=open wl1_basic_rate=default wl1_transmission_rate=auto wl1_transmission_power=full wl1_cts_protection_mode=auto wl1_frame_burst=enabled wl1_beacon_interval=100 wl1_dtim_interval=1 wl1_frag_threshold=2346 wl1_rts_threshold=2347 radius_server_ipaddr=0.0.0.0 radius_server_ipaddr_1=0 radius_server_ipaddr_2=0 radius_server_ipaddr_3=0 radius_server_ipaddr_4=0 radius_server_port=1812 radius_shared_key= radius_shared_key_interval=3600 filter_mode=disabled filter_type=allow filter_mac_1=00:00:00:00:00:00 filter_mac_2=00:00:00:00:00:00 filter_mac_3=00:00:00:00:00:00 filter_mac_4=00:00:00:00:00:00 filter_mac_5=00:00:00:00:00:00 filter_mac_6=00:00:00:00:00:00 filter_mac_7=00:00:00:00:00:00 filter_mac_8=00:00:00:00:00:00 filter_mac_9=00:00:00:00:00:00 filter_mac_10=00:00:00:00:00:00 filter_mac_11=00:00:00:00:00:00 filter_mac_12=00:00:00:00:00:00 filter_mac_13=00:00:00:00:00:00 filter_mac_14=00:00:00:00:00:00 filter_mac_15=00:00:00:00:00:00 filter_mac_16=00:00:00:00:00:00 filter_mac_17=00:00:00:00:00:00 filter_mac_18=00:00:00:00:00:00 filter_mac_19=00:00:00:00:00:00 filter_mac_20=00:00:00:00:00:00 filter_mac_21=00:00:00:00:00:00 filter_mac_22=00:00:00:00:00:00 filter_mac_23=00:00:00:00:00:00 filter_mac_24=00:00:00:00:00:00 filter_mac_25=00:00:00:00:00:00 filter_mac_26=00:00:00:00:00:00 filter_mac_27=00:00:00:00:00:00 filter_mac_28=00:00:00:00:00:00 filter_mac_29=00:00:00:00:00:00 filter_mac_30=00:00:00:00:00:00 filter_mac_31=00:00:00:00:00:00 filter_mac_32=00:00:00:00:00:00 filter_mac_33=00:00:00:00:00:00 filter_mac_34=00:00:00:00:00:00 filter_mac_35=00:00:00:00:00:00 filter_mac_36=00:00:00:00:00:00 filter_mac_37=00:00:00:00:00:00 filter_mac_38=00:00:00:00:00:00 filter_mac_39=00:00:00:00:00:00 filter_mac_40=00:00:00:00:00:00 log_mode=disabled log_ipaddr=0.0.0.0 chk_fw_hdr=enabled fw_extension=fim modle_id=LinksysWAP55AGv2 basic_realm=Linksys WAP55AG restore_defaults=0 firmware_version=1.1 my_firmware_version=1.0.22, Jan 26, 2005 customer_firmware_version=1.1, Jan 26, 2005 wl0_macaddr=00:12:17:77:41:30 wl1_macaddr=00:12:17:77:41:31 lan_macaddr=00:12:17:77:41:32

• ls
WAP55AG wlan0 -> ls nvram 2881 apcfg 3981 config.bin 3863 apcfg.bak 3981 defaults 85 apimg1.hdr 52 defaults.bak 85 apimg1 968660 452608 bytes free