Belkin F5D5231-4 v3

Belkin F5D5231-4 v3

Manuf (OEM/ODM): Edimax

(Est.) release date: March 2005
Country of manuf.: China

Type: router

Power: 12 VDC, 0.5 A
Connector type: barrel
Conn. measurements: 5 mm (OD), 2.5 mm (ID), 10 mm (LEN)

CPU1: Infineon ADM5120P
FLA1: 1 MiB 1,048,576 B <br />8,192 Kib <br />1,024 KiB <br />8 Mib <br />9.765625e-4 GiB <br /> (Macronix MX29LV800BTC-70)
RAM1: 4 MiB 4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (Winbond W981616CH-6 × 2)

Expansion IFs: none specified
Serial: yes, 4-pin header, populated, 3.3V TTL, (115200 8N1)

ETH chip1: Infineon ADM5120P
Switch: Infineon ADM5120P
LAN speed: 100M
LAN ports: 4
WAN speed: 100M
WAN ports: 1

Stock FW OS: Nucleus RTOS

Default IP address: 192.168.2.1
the IP 192.168.2.1 is used by 297 additional devices
of which 97 are Belkin devices

Ethernet OUI: 00:0E:2E (3 E, 14 W)

For a list of all currently documented Infineon (Lantiq) chipsets with specifications, see Infineon.

---

4-Port Router

 • Support page

"1244-00000382-010" and "Rev.A" is silkscreened on the board of the unit shown below.

A date code of 0512 (March 2005) is etched onto the bottom of the board

.. and is the basis for the release estimate in this entry.

Caps on this board are S.Y. branded.

Info derived from the serial dumps below would seem to indicate

the stock firmware is using the Nucleus RTOS.

Included PSU(s)

The power adapter included with the device is a DVE DVR-1250-B11.

ID/OD/Len measurements used in the main infobox are approximate.

DVE DVR-1250-B11 (more)
Input: 120 VAC ~ 60 Hz, ? A
Input connector: NEMA 1-15P Style: large, vertical  Manuf. in: China  Eff. level: 3
Output: 12 VDC, 0.5 A
Output connector: barrel (center +)  OD: ??  ID: ??  LEN: ??

Serial

Pinout

JP1 [3.3v] [RxD] [GND] [TxD]

Info derived from

• boot log

ADM5120 Boot:+P NetMall System Boot Copyright 2002-2003 ADMtek, Inc. CPU: ADM5120 Home Gateway Processor POST Version: 2.02.0154 Creation Date: 2005.01.31 Press <space> key three times to stop autoboot... 0 Verifying product code......PASS Boot Product Code!!! +P DHCPC:DHCP Client Started. Setting well_known IP DHCPS:DHCP Server Started. IpDefenseCfg_Config.status = 1 ========================================================================== Renaissance project: Command Line Interface. v.3.01.03 2005.03.23 ========================================================================== cmd> easyconf::start! waiting for data on port TCP 10101

• cmd> help

cmd> help Command Line Interface v0.01 ====================================================== rmem : Read memory. Usage : rmem <Address> [Num of Words] wmem : Write memory. Usage : wmem <Address> <Data0> [Data1] ... [Data7] rmi : read mii phy register. Usage : rmi <phy addr> <reg> wmi : write mii phy register. Usage : wmi <phy addr> <reg> <Data> time : Get current system time. Usage : time settime : Set system time. Usage : settime <hh:mm:ss> [yy/mm/dd] [TZ(GMT +/- hour)] help : List all commands. Usage : help mkdir : Make directories. Usage : mkdir <dir> create : Create files. Usage : create <file> cat : Concatenate files. Usage : cat <file> Press [q] to quit, any other key to continue.. ls : List directory contents. Usage : ls [dir] rm : Remove files. Usage : rm <file> rmdir : Remove directories. Usage : rmdir <DIRECTORY> copy : Copy files. Usage : copy <source> <destination> nvclear : Clear all of the NVFS files. Usage : nvclear routeShow : Show Route. Usage : routeShow mbufShow : Show Mbuf statistics. Usage : mbufShow ifShow : Dispaly network interface. Usage : ifShow <ifname> ifAllShow : Dispaly all network interface. Usage : ifAllShow taskShow : Show Task informations. Usage : taskShow Press [q] to quit, any other key to continue.. semShow : Show Semaphore informations. Usage : semShow timerShow : Show Timer informations. Usage : timerShow memShow : Show memory pool informations. Usage : memShow msgqShow : Show message queue informations. Usage : msgqShow eventShow : Show event group informations. Usage : eventShow knlShow : Show kernel resource informations. Usage : knlShow ipConfig : Configure interface address and subnet mask. Usage : ipConfig [ifname] [ip] [subnet mask] ipStatus : Change IP status. 1 for Enabled, 2 for Disabled.. Usage : ipStatus [ifname] [status] ipAdd : Add alias IP address.. Usage : ipAdd [ifname] [ip] [netmask] ipDel : Delete alias IP address.. Usage : ipAdd [ifname] [ip] [netmask] Press [q] to quit, any other key to continue.. arpAdd : Add an ARP entry to ARP table.. Usage : arpAdd [ip] <Ethernet Address> arpDel : Delete an ARP entry.. Usage : arpDel [ip] arpGet : Get the hardware address of a specify IP.. Usage : arpGet [ip] arpFlush : Flush ARP table.. Usage : arpFlush [ifname] ping : Ping a host.. Usage : ping [ip] [ms] dhcpcRelease: Release the IP address for the specified interface.. Usage : dhcpcRelease [ifname] dhcpcRenew: Renew the IP address for the specified interface.. Usage : dhcpcRenew [ifname] dhcpcLog : Show dhcpclog.. Usage : dhcpcLog dhcpcLogTest: Test dhcpclog.. Usage : dhcpcLogTest [line_num] dhcpsStart: Start DHCP Server.. Usage : dhcpsStart Press [q] to quit, any other key to continue.. dhcpsStop : Stop DHCP Server.. Usage : dhcpsStop dhcpsAddIp: Add static IP to the DHCP server. Usage : dhcpsAddIp [mac(00-00-00-00-00-00)] [ip(xxx.xxx.xxx.xxx)] dhcpsDelIp: Delete static IP from the DHCP server. Usage : dhcpsDelIp [ip(xxx.xxx.xxx.xxx)] dhcpsBindingNum: Print binding number of the DHCP server. Usage : dhcpsBindingNum dhcpsShowStatic: Print static IP of the DHCP server. Usage : dhcpsShowStatic natShow : Show NAT link table information. Usage : natShow natStart : Enable NAT function. Usage : natStart natStop : Disabled NAT function. Usage : natStop bindShow : Show NAT bind table information. Usage : bindShow upnpPMShow: Show UPnP port mapping table information. Usage : upnpPMShow Press [q] to quit, any other key to continue.. triggerPort: Set trigger port, when public port num is 0 will delete this entry.. Usage : triggerPort [index] [port] <protocol> [public port num] [start] [end] [protocol].... triggerShow: Show trigger port information. Usage : triggerShow icqShow : Show ICQ link information. Usage : icqShow mmsShow : Show MMS link information. Usage : mmsShow gethostbyname: gethostbyname. Usage : gethostbyname tftpc : TFTP client. Usage : tftpc <GET|PUT> <host> <remotename> <localname> tftps : Start TFTP server. Usage : tftps [dir] [timeout] update : Update runtime code (need to download image file "download" to /tmp). Usage : update setAccessHost: Add/delete access host. Usage : setAccessHost [NET(xx.xx.xx.xx)] [MASK (xx.xx.xx.xx)] <index> accessHostShow: Show access host information. Usage : accessHostShow Press [q] to quit, any other key to continue.. ripStart : Enable RIP . Usage : ripStart <version> ripStop : Disable RIP . Usage : ripStop ripShow : Show RIP table . Usage : ripShow connectTest: Test the Connecting mode. . Usage : connectTest [testing number] upnp : UPnP switch. . Usage : upnp [on/off] upnpTest : Test UPnP. . Usage : upnpTest [times]

• cmd> ifShow

cmd> ifShow lo (unit number 0): Flags: (0x8069) UP LOOPBACK MULTICAST ARP RUNNING Type: SOFTWARE_LOOPBACK Internet address: 127.0.0.1 Netmask 0xff000000 Subnetmask 0xff000000 Metric is 0 Maximum Transfer Unit size is 1536 0 packets received; 0 packets sent 0 multicast packets received 0 multicast packets sent 0 input errors; 0 output errors 0 collisions; 0 dropped adm (unit number 0): Flags: (0x9863) UP BROADCAST MULTICAST ARP RUNNING Type: ETHERNET_CSMACD Internet address: 192.168.2.1 Broadcast address: 192.168.2.255 Netmask 0xffffff00 Subnetmask 0xffffff00 Ethernet address is 00:0e:2e:5d:8e:b7 Metric is 0 Maximum Transfer Unit size is 1500 0 packets received; 17 packets sent 0 multicast packets received 17 multicast packets sent 0 input errors; 0 output errors 0 collisions; 0 dropped adm (unit number 1): Flags: (0x8863) UP BROADCAST MULTICAST ARP RUNNING Type: ETHERNET_CSMACD Ethernet address is 00:0e:2e:5d:8e:b8 Metric is 0 Maximum Transfer Unit size is 1500 0 packets received; 9 packets sent 0 multicast packets received 0 multicast packets sent 0 input errors; 0 output errors 0 collisions; 0 dropped

• cmd> taskShow

cmd> taskShow Task Table List ------------------------------------------------- Name Priority Status ================================================= 0. KnlTask 0 QUEUE_SUSPEND 1. tNetTas 50 SEMAPHORE_SUSPEND 2. tNvTask 100 SLEEP_SUSPEND 3. tDhcpcT 100 QUEUE_SUSPEND 4. tDnsPro 100 SEMAPHORE_SUSPEND 5. tDhcpsT 100 QUEUE_SUSPEND 6. tSntpc 100 READY 7. tHttpD 100 SEMAPHORE_SUSPEND 8. tHtpTsk 100 QUEUE_SUSPEND 9. clitask 5 READY 10. tUpnpD 100 READY 11. tUpnpTs 100 QUEUE_SUSPEND 12. tEasyCo 100 SEMAPHORE_SUSPEND 13. tDhcpPi 100 SLEEP_SUSPEND 14. powerbu 100 SLEEP_SUSPEND -------------------------------------------------

• cmd> memShow

cmd> memShow Memory Pool List -------------------------------------------------------------------------- Name StartAddr Size MinAlloc Available Type TasksWaiting =========================================================================== 0. ShaMem 0x803F0000 65536 48 30896 FIFO 0 1. KenMem 0x802EB800 1067008 48 334292 FIFO 0 2. DskMem 0x80235000 747520 48 388 FIFO 0 3. UsrMem 0x80190394 674924 48 419956 FIFO 0 ---------------------------------------------------------------------------

• cmd> knlShow

cmd> knlShow Task Table List ------------------------------------------------- Name Priority Status ================================================= 0. KnlTask 0 QUEUE_SUSPEND 1. tNetTas 50 READY 2. tNvTask 100 READY 3. tDhcpcT 100 QUEUE_SUSPEND 4. tDnsPro 100 SEMAPHORE_SUSPEND 5. tDhcpsT 100 QUEUE_SUSPEND 6. tSntpc 100 READY 7. tHttpD 100 READY 8. tHtpTsk 100 QUEUE_SUSPEND 9. clitask 5 READY 10. tUpnpD 100 SEMAPHORE_SUSPEND 11. tUpnpTs 100 QUEUE_SUSPEND 12. tEasyCo 100 SEMAPHORE_SUSPEND 13. tDhcpPi 100 SLEEP_SUSPEND 14. powerbu 100 SLEEP_SUSPEND ------------------------------------------------- Memory Pool List -------------------------------------------------------------------------- Name StartAddr Size MinAlloc Available Type TasksWaiting =========================================================================== 0. ShaMem 0x803F0000 65536 48 30896 FIFO 0 1. KenMem 0x802EB800 1067008 48 333716 FIFO 0 2. DskMem 0x80235000 747520 48 388 FIFO 0 3. UsrMem 0x80190394 674924 48 420024 FIFO 0 --------------------------------------------------------------------------- Semaphore Table List ------------------------------------------------------- Name Type Count TasksWaitting ======================================================= 0. MFS_SEM FIFO 1 0 1. netSem FIFO 0 1 2. splSem FIFO 1 0 3. hosttbl FIFO 1 0 4. mblksem PRIORITY 1 0 5. mclsem PRIORITY 1 0 6. FLSH FIFO 1 0 7. sio_Rx0 FIFO 0 0 8. sio_RT0 FIFO 0 0 9. NVRAM FIFO 1 0 10. downloa FIFO 1 0 11. user_cf FIFO 1 0 12. pppoe_c FIFO 1 0 13. pptp_cf FIFO 1 0 14. dhcpc_c FIFO 1 0 15. dhcpcLo FIFO 1 0 16. DhcpcSe FIFO 1 0 17. dhcpcMu FIFO 1 0 18. dhcpcEv FIFO 1 0 19. dhcp_ti FIFO 1 0 20. leaseSe FIFO 1 0 21. ip_cfg FIFO 1 0 22. nat_cfg FIFO 1 0 23. route_c FIFO 1 0 24. dns_rel FIFO 1 0 25. dhcps_c FIFO 1 0 26. time_zo FIFO 1 0 27. sntpc_c FIFO 1 0 28. sotSem FIFO 1 0 29. sorSem FIFO 1 0 30. sosSem FIFO 1 0 31. ip_fire FIFO 1 0 32. ip_defe FIFO 1 0 33. ip_filt FIFO 1 0 34. url_fil FIFO 1 0 35. http_cf FIFO 1 0 36. access_ FIFO 1 0 37. ethftr_ FIFO 1 0 38. upnp_cf FIFO 1 0 39. sotSem FIFO 1 0 40. sorSem FIFO 1 0 41. sosSem FIFO 1 0 42. sotSem FIFO 1 0 43. sorSem FIFO 1 0 44. sosSem FIFO 1 0 45. sotSem FIFO 1 0 46. sorSem FIFO 1 0 47. sosSem FIFO 1 0 48. sotSem FIFO 1 0 49. sorSem FIFO 1 0 ------------------------------------------------------- Timer Table List ------------------------------------------------------- Name Status InitialTime Expirations ======================================================= 0. t0 Enable 100 0 <.. the system crashes at this point (or before)>

bootloader info

• text on autoboot abort

ADM5120 Boot:+P NetMall System Boot Copyright 2002-2003 ADMtek, Inc. CPU: ADM5120 Home Gateway Processor POST Version: 2.02.0154 Creation Date: 2005.01.31 Press <space> key three times to stop autoboot... 3 Net Routing Table: Destination Gateway NetMask Flags Used Hops Interface ------------------------------------------------------------------------------- POST Menu ========================= [1] Xmodem Download [2] TFTP Client Download [3] TFTP Server Download [4] Print Boot Params [5] Set Boot Params [6] Set Boot Mode [7] Exit Please enter your number:

• boot params
Please enter your number: 4 Print Boot Parameters. ========================== Serial number: 506B3000725 Hardware version: F5D5231-4 Mac addres: 00-0e-2e-5d-8e-b7 Number of Mac address: 2 Number of configured interface: 0

Images

• 

  board top

• 

  board bottom