Asecam B8IPC-4KPOE

Asecam B8IPC-4KPOE

Country of manuf.: China

Type: IP camera

Power: 12 VDC, ? A
Connector type: barrel
PoE tag: 802.3af, standard

CPU1: Fullhan FH8856V100
FLA1: 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (BoyaMicro BY25Q64ES)
RAM1: 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (Brand? embedded)

Expansion IFs: none specified
Serial: yes, 3-pin header, (115200,8,N,1)

ETH chip1: Fullhan FH8856V100
ETH chip2: JLSemi JL1101
LAN speed: 100M
LAN ports: 1

Stock bootloader: U-Boot 2010.06

Stock FW OS: Linux 3.0.8

Flags: PoE in, microphone

Default IP address: 192.168.1.10
the IP 192.168.1.10 is used by 6 additional devices
of which 0 are Asecam devices
Default login user: admin
Default login password: 123456
admin:123456 credentials used by 1 additional devices
of which 0 are Asecam devices

Ethernet OUI: F6:3A:80

Fullhan not currently documented.

---

Overview

This camera is based on a Vatilon PB1 module. It appears that Asecam is merely a white-label brand, and did not make any modifications to the Vatilon hardware or software.

Specifications

• IP Camera

Processor: Fullhan FH8856V100

Image sensor: GalaxyCore GC4653 4MP 1/3" (Vatilon says it's a GC8053, but both OpenIPC's ipctool and examination of the stock firmware indicate that it's a GC4653.)

Memory: 128MB embedded RAM; 8MB SPI NOR flash (BoyaMicro BY25Q64ES)

Video: 8MP H.265 (HEVC) or H.264 (Despite the apparent 4MP sensor, the encoder does produce a 3840x2160 video stream.)

LAN: JLSemi JL1101 FE (10/100)

Ports: 1x FE (RJ45) PoE

Links

• Asecam product listing
• Vatilon PB1 module product page
• Vatilon software downloads
• Asecam software downloads
• GalaxyCore GC4653 datasheet
• JLSemi JL11x1 datasheet

Bootlog

• Bootlog • >>

ROM: Use nor flash. ROM: Init DDR..Training done. ROM: Ok U-Boot 2010.06 (Jul 26 2022 - 14:22:43) DRAM: 128 MiB SF: Got idcode 68 40 17 68 40 use default flash ops... spi_flash_probe_default multi wire open flag is 0 In: serial Out: serial Err: serial MMC: FH_MMC: 0 MMC FLASH INIT: No card on slot! Net: set to RMII FH EMAC Hit any key to stop autoboot: 0 SF: Got idcode 68 40 17 68 40 use default flash ops... spi_flash_probe_default multi wire open flag is 0 current fw 10889 MAC: f6:a2:00:00:81:54 set to RMII PHY OUI: 0x937c4024 at phyid: 0 operating at 100M full duplex mode retry 1 retry 2 net update try timeout SF: Got idcode 68 40 17 68 40 use default flash ops... spi_flash_probe_default multi wire open flag is 0 8192 KiB default_flash at 0:0 is now current device ## Booting kernel from Legacy Image at a1000000 ... Image Name: Linux-3.0.8 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2393484 Bytes = 2.3 MiB Load Address: a0008000 Entry Point: a0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK prepare atags Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.0.8 (appollo@Trusty) (gcc version 5.5.0 (b220190606) ) #1 Tue Jul 26 18:06:43 CST 2022 [ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: FH8852 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 9144 [ 0.000000] Kernel command line: mem=36M console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs mtdparts=spi_flash:320K(uboot),2560K(kernel),4096K(appfs),832K(custom),320K(config),64K(data) [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 36MB = 36MB total [ 0.000000] Memory: 31424k/31424k available, 5440k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xc2800000 - 0xfe000000 ( 952 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc2400000 ( 36 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .init : 0xc0008000 - 0xc00e5000 ( 884 kB) [ 0.000000] .text : 0xc00e5000 - 0xc04ae000 (3876 kB) [ 0.000000] .data : 0xc04ae000 - 0xc04d2600 ( 146 kB) [ 0.000000] .bss : 0xc04d2624 - 0xc04f07f8 ( 121 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:128 [ 0.000000] timer mult: 0xa0000000, timer shift: 0x1b [ 0.000000] sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 85899ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [ttyS0] enabled [ 0.176983] Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032) [ 0.240010] pid_max: default: 32768 minimum: 301 [ 0.244628] Mount-cache hash table entries: 512 [ 0.249346] CPU: Testing write buffer coherency: ok [ 0.254483] devtmpfs: initialized [ 0.259720] NET: Registered protocol family 16 [ 0.264208] FH8856 board init [ 0.331922] bio: create slab <bio-0> at 0 [ 0.333719] cannot get dmac0_hclk [ 0.338494] fh_dmac fh_dmac.0: FH DMA Controller, 6 channels [ 0.344268] usbcore: registered new interface driver usbfs [ 0.348045] usbcore: registered new interface driver hub [ 0.353230] usbcore: registered new device driver usb [ 0.361195] cfg80211: Calling CRDA to update world regulatory domain [ 0.366612] Switching to clocksource fh_clocksource [ 0.370063] Switched to NOHz mode on CPU #0 [ 0.408356] NET: Registered protocol family 2 [ 0.410043] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.417070] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.423792] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.430058] TCP: Hash tables configured (established 2048 bind 2048) [ 0.436285] TCP reno registered [ 0.439409] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.445241] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.451793] NET: Registered protocol family 1 [ 0.456235] RPC: Registered named UNIX socket transport module. [ 0.461655] RPC: Registered udp transport module. [ 0.466266] RPC: Registered tcp transport module. [ 0.470962] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.895715] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.917422] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 1.930233] msgmni has been set to 61 [ 1.940723] NET: Registered protocol family 38 [ 1.942355] io scheduler noop registered (default) [ 1.956849] fh_pwm_probe: clk_rate: 50000000 [ 1.962858] PWM driver, Number: 8, IO base addr: 0xc3070000 [ 1.974725] ttyS.0: ttyS0 at MMIO 0xf0700000 (irq = 30) is a ttyS [ 1.983052] ttyS.1: ttyS1 at MMIO 0xf0800000 (irq = 31) is a ttyS [ 2.005129] brd: module loaded [ 2.041674] CLK misc driver init successfully [ 2.075047] m25p80 spi0.0: found BY25Q64AS, expected m25p80 [ 2.078040] m25p80 spi0.0: set_qe : 235 default not support multi wire.. [ 2.085497] m25p80 spi0.0: BY25Q64AS (8192 Kbytes) [ 2.090698] DEBUG-CMDLINE-PART: parsing <320K(uboot),2560K(kernel),4096K(appfs),832K(custom),320K(config),64K(data)> [ 2.102200] DEBUG-CMDLINE-PART: partition 5: name <data>, offset ffffffff, size 10000, mask flags 0 [ 2.112078] DEBUG-CMDLINE-PART: partition 4: name <config>, offset ffffffff, size 50000, mask flags 0 [ 2.122149] DEBUG-CMDLINE-PART: partition 3: name <custom>, offset ffffffff, size d0000, mask flags 0 [ 2.132223] DEBUG-CMDLINE-PART: partition 2: name <appfs>, offset ffffffff, size 400000, mask flags 0 [ 2.142295] DEBUG-CMDLINE-PART: partition 1: name <kernel>, offset ffffffff, size 280000, mask flags 0 [ 2.152466] DEBUG-CMDLINE-PART: partition 0: name <uboot>, offset ffffffff, size 50000, mask flags 0 [ 2.162445] DEBUG-CMDLINE-PART: mtdid=<spi_flash> num_parts=<6> [ 2.168893] 6 cmdlinepart partitions found on MTD device spi_flash [ 2.175672] Creating 6 MTD partitions on "spi_flash": [ 2.181192] 0x000000000000-0x000000050000 : "uboot" [ 2.206403] 0x000000050000-0x0000002d0000 : "kernel" [ 2.227346] 0x0000002d0000-0x0000006d0000 : "appfs" [ 2.248216] 0x0000006d0000-0x0000007a0000 : "custom" [ 2.269267] 0x0000007a0000-0x0000007f0000 : "config" [ 2.290212] 0x0000007f0000-0x000000800000 : "data" [ 2.343087] console [netcon0] enabled [ 2.343970] netconsole: network logging started [ 2.381581] resource: start=e0700000, len=00100000 [ 2.383764] base=0xc3200000 (after adjust) [ 2.388270] fh_otg_driver_probe: mapped PA 0xe0700000 to VA 0xc3200000 [ 2.495275] Core Release: 4.00a [ 2.495595] Setting default values for core params [ 2.700371] dma_enable :1 [ 2.700394] dma_desc_enable :1 [ 2.903012] Using Descriptor DMA mode [ 2.903900] Periodic Transfer Interrupt Enhancement - disabled [ 2.910292] Multiprocessor Interrupt Enhancement - disabled [ 2.916350] OTG VER PARAM: 0, OTG VER FLAG: 0 [ 2.921129] FH OTG HCD INIT (c104b780) [ 2.925193] hcd regs before base(c3200000) [ 2.929718] fh_otg fh_otg: FH OTG Controller [ 2.934448] fh_otg fh_otg: new USB bus registered, assigned bus number 1 [ 2.941727] fh_otg fh_otg: irq 27, io mem 0x00000000 [ 2.947076] Init: Power Port (0) [ 2.950742] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.957981] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.965907] usb usb1: Product: FH OTG Controller [ 2.970933] usb usb1: Manufacturer: Linux 3.0.8 fh_otg_hcd [ 2.976890] usb usb1: SerialNumber: fh_otg [ 2.987138] hub 1-0:1.0: USB hub found [ 2.988142] hub 1-0:1.0: 1 port detected [ 3.001905] i2c /dev entries driver [ 3.007048] I2C driver: [ 3.007061] platform registration... [ 3.010609] Clock: 50000khz, Standard-mode HCNT:LCNT = 212:249 [ 3.017154] tx fifo depth: 16, rx fifo depth: 16 [ 3.030040] I2C - (dev. name: fh_i2c - id: 0, IRQ #11 [ 3.030053] IO base addr: 0xc30a0000) [ 3.036756] I2C driver: [ 3.036764] platform registration... [ 3.043393] Clock: 50000khz, Standard-mode HCNT:LCNT = 212:249 [ 3.049980] tx fifo depth: 16, rx fifo depth: 16 [ 3.074644] I2C - (dev. name: fh_i2c - id: 1, IRQ #12 [ 3.074656] IO base addr: 0xc30a8000) [ 3.108848] card0 disconnected! [ 3.123811] TCP cubic registered [ 3.124230] NET: Registered protocol family 17 [ 3.129132] lib80211: common routines for IEEE802.11 drivers [ 3.135334] Registering the dns_resolver key type [ 3.140519] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5 [ 3.187978] GMAC driver: [ 3.187993] platform registration... [ 3.191672] using random MAC address: ee:22:ba:91:4a:ac [ 3.202073] fh_gmac fh_gmac.0: eth0: mixed HW and IP checksum settings. [ 3.206201] fh_gmac fh_gmac.0: eth0: mixed no checksumming and other settings. [ 3.214312] eth0 - (dev. name: fh_gmac - id: 0, IRQ #15 [ 3.214325] IO base addr: 0xc30c8000) [ 3.250698] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 3.286267] aes driver registered [ 3.290350] Freeing init memory: 884K starting pid 489, tty '': '/etc/init.d/rcS' [RCS]: /etc/init.d/S01udev Starting udev: [ OK ] [RCS]: /etc/init.d/S03network starting pid 575, tty '/dev/ttyS0': '/bin/login' IPCam login: