Alcatel-Lucent G-011G-P
Jump to navigation
Jump to search
Alcatel-Lucent G-011G -P
Type: fiber gateway, ONT
Power: 12 VDC, 1 A
Connector type: barrel
CPU1: Broadcom BCM68385
FLA1: 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (Toshiba TN58NVG0S3ETA00)
RAM1: 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (Winbond W631GG6KB-15)
Expansion IFs: none specified
Serial: yes, 4-pin header, 3.3V TTL, (115200 8N1), X2
ETH chip1: Broadcom BCM68385
LAN speed: 1GbE
LAN ports: 1
Ethernet OUI: none specified
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
Optical Network Terminal
Models
- Alcatel-Lucent G-011G-P
- Alcatel-Lucent I-011G-P
- Alcatel-Nokia G-010G-Q/R
- Alcatel-Nokia XS-010X-Q
Serial
Boot log
| • bootlog • >> |
|---|
CFEROM --> CFERAM0 --> HERE
************************************************************
* *
* Bootloader For Bcm9638x *
* *
************************************************************
Version : V9.09.20
Buile Date : Oct 24 2014-11:12:05
CPU : Soc(68385_B0) MIPS32(240Mhz) DDR(333Mhz) Bus(240Mhz) RDP(400Mhz)
DRAM : 128 MB
NAND : 128 MB 4Bits Ecc
DEVxID : 0x00a20101
Usrinfo : 0x00a20101
Hit password to stop autoboot @ 3 ��2 ��1
loading image..
ImageB crc checking
### CRAMFS loading 'vmlinux.lz' from imageb to 0x82800000
### CRAMFS load complete: 1143677 bytes loaded to 0x82800000
Entry at 0x8026ea90
Closing network.
Starting program at 0x8026ea90
Linux version 3.4.11-rt19+ (junjie@GPONBUSW1) (gcc version 4.6.2 (Buildroot 2011.11) ) #1 SMP PREEMPT Wed Feb 11 10:54:08 CST 2015
*** Voice Board id is not initialized properly ***
968385GSP prom init
CPU revision is: 0002a080 (Broadcom BMIPS4350)
Determined physical RAM map:
memory: 01400000 @ 06c00000 (reserved)
memory: 00400000 @ 06800000 (reserved)
memory: 06800000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00006800
Movable zone start PFN for each node
Early memory PFN ranges
0: 0x00000000 -> 0x00006800
On node 0 totalpages: 26624
free_area_init_node: node 0, pgdat 8031f940, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 176 pages used for memmap
Normal zone: 22352 pages, LIFO batch:3
PERCPU: Embedded 7 pages/cpu @810d3000 s5088 r8192 d15392 u32768
pcpu-alloc: s5088 r8192 d15392 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 26416
Kernel command line: ro noinitrd irqaffinity=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 101864k/106496k available (2460k kernel code, 4632k reserved, 676k data, 176k init, 0k highmem)
Preemptible hierarchical RCU implementation.
NR_IRQS:256
console [ttyS0] enabled
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
Calibrating delay loop... 237.05 BogoMIPS (lpj=118528)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
--Kernel Config--
SMP=1
PREEMPT=1
DEBUG_SPINLOCK=0
DEBUG_MUTEXES=0
Broadcom Logger v0.1 Feb 11 2015 10:49:26
CPU revision is: 0002a080 (Broadcom BMIPS4350)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Brought up 2 CPUs
NET: Registered protocol family 16
PMC Driver Init... done.
bio: create slab <bio-0> at 0
bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
skbFreeTask created successfully
�[0;34mBLOG v3.0 Initialized�[0m
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 Feb 11 2015 10:52:47 initialized
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
init_bcm_tstamp: unhandled mips_hpt_freq=120000000, adjust constants in bcm_tstamp.c
bcm_tstamp initialized, (hpt_freq=120000000 2us_div=120 2ns_mult=0 2ns_shift=0)
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 198
io scheduler noop registered (default)
Broadcom NAND controller (BrcmNand Controller)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0
brcmnand_read_id: CS0: dev_id=98d19015
After: NandSelect=40000001, nandConfig=15142200
brcmnand_probe: Ecc level set to 1, sectorSize=512 from ID table
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 6574845b
timing2 not adjusted: 00001e96
BrcmNAND mfg 98 d1 TOSHIBA TC58NVG0S3ETA00 128MB on CS0
Found NAND on CS0: ACC=f7441010, cfg=15142200, flashId=98d19015, tim1=6574845b, tim2=00001e96
BrcmNAND version = 0x80000500 128MB @00000000
brcmnand_scan: B4 nand_select = 40000001
brcmnand_scan: After nand_select = 40000001
handle_acc_control: default CORR ERR threshold 1 bits
ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 5.0 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_2k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=35, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_descr
Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0
Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0
brcmnand_reset_corr_threshold: default CORR ERR threshold 1 bits for CS0
brcmnand_reset_corr_threshold: CORR ERR threshold changed to 3 bits for CS0
brcmnandCET: Status -> Deferred
Creating 11 MTD partitions on "brcmnand.0":
0x000000000000-0x000000100000 : "boota"
0x000000100000-0x000000200000 : "bootb"
0x000000200000-0x000000400000 : "configa"
0x000000400000-0x000000600000 : "configb"
0x000000600000-0x000002200000 : "imagea"
0x000002200000-0x000003000000 : "imagec0"
0x000003000000-0x000004c00000 : "imageb"
0x000004c00000-0x000005a00000 : "imagec1"
0x000005a00000-0x000005b00000 : "misca"
0x000005b00000-0x000005c00000 : "miscb"
0x000005c00000-0x000008000000 : "reserved"
i2c /dev entries driver
brcmboard: brcm_board_init entry
#### g_product_id=0x00a20101 g_flag_5srst=0x00000000####
Alloc watchdog timer 2
Serial: BCM63XX driver $Revision: 3.00 $
�[0;33mMagic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)�[0m
ttyS0 at MMIO 0xb4e00500 (irq = 9) is a BCM63XX
ttyS1 at MMIO 0xb4e00520 (irq = 10) is a BCM63XX
TCP: cubic registered
NET: Registered protocol family 17
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
8021q: 802.1Q VLAN Support v1.8
VFS: Mounted root (cramfs filesystem) readonly on device 31:6.
Freeing unused kernel memory: 176k freed
init started: BusyBox v1.9.2 (2014-01-06 10:43:27 CST)
tar: chdir(/dev/shm): No such file or directory
grep: /etc/network/options: No such file or directory
grep: /etc/network/options: No such file or directory
grep: /etc/network/options: No such file or directory
jffs2: Empty flash at 0x0001300c ends at 0x00013800
#mount /dev/mtdblock2 --> /mnt/rwdir ok
# num is 10,nothing need to do
cp: cannot stat '/etc/resolv.conf.rwdir': No such file or directory
cat: can't open '/dev/rgs_logger': No such file or directory
ifconfig: SIOCGIFFLAGS: No such device
# Created object <system>
RDPA lan init
# Created object <port/index=lan0>
# Created object <egress_tm/dir=ds,index=0>
# Created object <bridge/index=0>
RDPA lan init end
rdpa filter init start!!
# Created object <filter>
rdpa filter init end
ONT>SSP: Set rlimit: S = 0x100000, H = 0x7fffffff
TMR: Set rlimit: S = 0x100000, H = 0x7fffffff
Starting Application: 0x00002000, /bin/TimerMgr................Done. elapsed time:(227)ms
Update timer: curTime=0000319b, gTmrTimerMsCounter=00000000
LOG: Set rlimit: S = 0x100000, H = 0x7fffffff
Starting Application: 0x00001000, /bin/LogMgr................Done. elapsed time:(123)ms
MMR: Set rlimit: S = 0x100000, H = 0x7fffffff
actImage[1], PartId[6], custom[UUAL] sys_cfg[/etc/sys.cfg.alu]
cp: cannot stat '/etc/sys.cfg.alu': No such file or directory
Starting Application: 0x00007000, /bin/MiscMgr................Done. elapsed time:(625)ms
d6885a:Exit SSP -->log, msg 0x4000c,elapsed time:706 ms
Mount Backup[/dev/mtdblock4] as cramfs...Success.
major ID[0xa2] minor ID[0x1]
PMR: Set rlimit: S = 0x100000, H = 0x7fffffff
Starting Application: 0x00004000, /bin/PonMgr................Done. elapsed time:(344)ms
NET: Set rlimit: S = 0x100000, H = 0x7fffffff
sh: can't open /sbin/ath_wifi.sh
Starting Application: 0x00009000, /bin/NetMgr................Done. elapsed time:(475)ms
EMR: Set rlimit: S = 0x100000, H = 0x7fffffff
Starting Application: 0x00005000, /bin/EthMgr................Done. elapsed time:(387)ms
MEC: Set rlimit: S = 0x100000, H = 0x7fffffff
Starting Application: 0x00003000, /bin/MecMgr................Done. elapsed time:(3854)ms
15f33db:Exit SSP -->ssp, msg 0x50000,elapsed time:10711 ms
16b9c4b:Exit MEC -->pmr, msg 0xc0002,elapsed time:804 ms
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
9107ca7 9107ca7 9107ca7
ifconfig: SIOCGIFFLAGS: No such device
184f1c9:Exit MEC -->net, msg 0xc0002,elapsed time:1653 ms
192bb33:Exit MEC -->emr, msg 0xc0002,elapsed time:898 ms
Powered down
1a7333e:Exit MEC -->emr, msg 0xc0004,elapsed time:1258 ms
i/f name: brdg
gem ids:
INFO: ALL APPs are ready.
1a9514a:Exit NET -->mec, msg 0xc0000,elapsed time:4858 ms
start config net connection for WAN[0]
|
Images
